SX Series

316 cast stainless steel pumps with non-clog impellers for municipal, industrial and agricultural wastewater The SX Series pumps have non-clog impellers designed for high volume and lift performance. All wear and "wet" parts such as impeller, wear-plate, oil housing, pump housing and inner pump top are made of cast 316 stainless material. The elastomers such as o-rings, lip seals and gaskets are made of FKM. Standard power cable is made of oil-resistant material. Special installation can be made with EPDM power-cable and elastomers. (BUNA-N also available).
View ModelsRequest Information
Download
Series Curves (PDF)
  • All parts exposed to pumped liquids are made of 316 stainless steel.
  • Elastomers are made of FKM.
  • Longer power cord – Standard 33ft. power cord.
  • Three seal motor protection – Motor is protected by double mechanical seals. Lower seal made of silicon carbide/silicon carbide and upper seal is made of carbon/ceramic. An additional lip seal has been installed above the impeller to help prevent abrasives such as dirt, silt or sand from entering into the seal chamber.
  • Winding protection and (NEMA) Class F motor insulation allows motor temperature to raise to 230°F, superior to pumps with Class A and B insulation. Automatic switch turns pump motor off if temperature and/or amp draw raises too high. When the motor cools the switch will automatically reset and the pump will turn back on.
  • Each pump is tested at factory, both for performance as well as safety. Level controls and level control systems are available.
  • Specifications dependent on model and may change without notice
  • Sales Brochure
  • Operation Manual
  • Pump Dimensions
  • Exploded View
  • Parts List
  • Specifications
  • Warranty
  • SOOW Power Cord EPDM Power Cord Seal Minder® Cord Manual Starter Box Auto Starter Box Simplex Three Phase Control Panels Duplex Three Phase Control Panel Seal Minder® & Tank Alarm Seal Minder Relay 316 Stainless Steel Slide Rails Slide Rail Accessories

    Select Model

    Model Motor Rating (HP) Voltage Rated Amps Discharge Connection Max Solids Max Head Max GPM Phase Learn More
    SX08CSS-208T Curves
    1 208, 3ph-60Hz 3.15 2" NPT-M 2" 48' 95 3 Details
    SX08CSS-230T Curves
    1 230, 3ph-60Hz 3 2" NPT-M 2" 48' 95 3 Details
    SX08CSS-460T Curves
    1 460, 3ph-60Hz 1.5 2" NPT-M 2" 48' 95 3 Details
    SX08CSS-575T Curves
    1 575, 3ph-60Hz 1.2 2" NPT-M 2" 48' 95 3 Details
    SX15CSS-208T Curves
    2 208, 3ph-60Hz 6.3 3" NPT-M 1.6" 42' 220 3 Details
    SX15CSS-230T Curves
    2 230, 3ph-60Hz 6 3" NPT-M 1.6" 42' 220 3 Details
    SX15CSS-460T Curves
    2 460, 3ph-60Hz 3 3" NPT-M 1.6" 42' 220 3 Details
    SX15CSS-575T Curves
    2 575, 3ph-60Hz 2.3 3" NPT-M 1.6" 42' 220 3 Details
    SX22CSS-208T Curves
    3 208, 3ph-60Hz 9.45 3" NPT-M 1.6" 45' 270 3 Details
    SX22CSS-230T Curves
    3 230, 3ph-60Hz 9 3" NPT-M 1.6" 45' 270 3 Details
    SX22CSS-460T Curves
    3 460, 3ph-60Hz 4.5 3" NPT-M 1.6" 45' 270 3 Details
    SX22CSS-575T Curves
    3 575, 3ph-60Hz 3.2 3" NPT-M 1.6" 45' 270 3 Details
    SX37CSS-208T Curves
    5 208, 3ph-60Hz 14.7 3" flange w/ 4" NPT-F discharge (3" NPT-M optional) 1.6" 62' 360 3 Details
    SX37CSS-230T Curves
    5 230, 3ph-60Hz 14 3" flange w/ 4" NPT-F discharge (3" NPT-M optional) 1.6" 62' 360 3 Details
    SX37CSS-460T Curves
    5 460, 3ph-60Hz 7 3" flange w/ 4" NPT-F discharge (3" NPT-M optional) 1.6" 62' 360 3 Details
    SX37CSS-575T Curves
    5 575, 3ph-60Hz 5.5 3" flange w/ 4" NPT-F discharge (3" NPT-M optional) 1.6" 62' 360 3 Details
    SX55CSS-230T Curves
    7.5 230, 3ph-60Hz 21 4" NPT-F 2.5" 78' 450 3 Details
    SX55CSS-460T Curves
    7.5 460, 3ph-60Hz 10.5 4" NPT-F 2.5" 78' 450 3 Details
    SX55CSS-575T Curves
    7.5 575, 3ph-60Hz 7.6 4" NPT-F 2.5" 78' 450 3 Details
    SX75CSS-460T Curves
    10 460, 3ph-60Hz 15 4" NPT-F 2.5" 99' 590 3 Details
    SX75CSS-575T Curves
    10 575, 3ph-60Hz 10.5 4" NPT-F 2.5" 99' 590 3 Details